Description 

• Replaces the restrictive mesh element in the intake manifold.
• It increases air flow to the engine, maximizing horsepower.
• Constructed from billet for extra durability and strength
• Tapered design to allow more air flow
• Suits all Supercharger models and all 13+ N/A Models
• DOES NOT SUIT NON SUPERCHARGERD MODELS 2012 AND EARILER

Fits Solas Yamaha YV, YS Dynafly, YS Concord, and YS-TP series impeller shafts.

Description 

• Our new Yamaha Engine Block Cooling plate allows for up to 3 fittings to be fitted for maximum water flow into you Yamaha 1.8 engine block. Injection points target know engine ‘Hot Spot” and directs initial cooling around No#2 cylinder which is common for detonation and overheating in high boost applications.
• Billet anodized construction allowing 1,2 or 3 fittings to be installed
• Fits all 1.8 Yamaha engines (may require o-ring for early models)
• Allows for maximum cooling to the engine under high boost
• Race proved in a closed course and endurance

Description 

High Strength Bolt kit for direct replacement of OEM Flywheel bolts that are prone to failure on modified watercraft.

Suits all Yamaha 1.8 models

Suit SeaDoo 4-tec 1503 and 1630 ACE engine

Sold in Pack of 6

Description 

Billet anodized fitting to replace anode block which allows for extra cooling water to be added or removed from the rear of Yamaha 1.8 Engine block to suit your cooling needs.  A must for any modified recreational or race craft.

Description 

Our Yamaha 2015+ VXR/VXS, FX SVHO rear exhaust kit will eliminate any exhaust restriction, increase engine performance and give your Ski the “This means business look” with the Huge 3 inch Billet anodized outlet.

Molded Black silicone hose for easy install
Billet anodized black 3-inch exhaust outlet
Billet anodized block off plate
Eliminates restrictive sound suppression baffles
Silicone hose reduces exhaust resonance and droning
A must for High horsepower/ Racecraft

Designed for Yamaha FX WaveRunners, this all-new system delivers a powerful audio option never before seen on PWC. This JL AUDIO® SlamPak™ is sure to transform your WaveRunner into a serious music machine, adding even more enjoyment to every minute you spend on the water.

• Also includes plug-and-play harness with Deutsche connectors, marine-grade circuit breaker, power cable, speaker cable, audio cable, stainless steel mounting brackets, and hardware
• Pair of waterproof VeX™ speaker pods houses two high-performance 6.5" marine-grade coaxial speakers to deliver loud, clean audio in real-world marine environments
• Neatly tucked away, is a custom-formed Stealthbox® subwoofer system, equipped with a potent 8.8" marine subwoofer, generating powerful bass and optimized for open-air environments
• Compact, 500 watt, 4-channel amplifier to power the entire system
• MBT-CRX Bluetooth® controller/receiver connects to your Bluetooth® device and accesses your playlist wirelessly
• Exceeds industry standards for corrosion resistance and UV exposure

Designed not just for cutting edge performance but killer style! Same best selling Worx Racing paddle now with billet insert for 4 point adjustment to personalize your watercraft to your own unique riding style! 

Specifically designed for the unique handling characteristics of the Yamaha FX and FZ hulls.

Includes backing rails and all necessary hardware.

Product benefits include:

- Enhanced control, stability, and predictability, the ski stays hooked and does not throw you off
- Stops the ski from sinking in the back in tight turns like stock sponsons
- Allows for Greater corner entry speed
- Maximized top speed performance by creating less drag
- Superior straight line stability
- Easy installation to stock mounting points

IJSBA legal for all classes

Description

Fits 2014-2018 FX SVHO/ HO models.

Please call 800-940-3000 or email info@bms-racing.com for custom orders.

View colors HERE

Description

Fits 2014-2018 FX SVHO Cruiser models.

Please call 800-940-3000 or email info@bms-racing.com for custom orders.

View colors HERE

Fits all Yamaha models
Battery Details:

Description 

• Billet Drive coupler for Yamaha 1.8 Engine
• Fits any 1.8 Yamaha Engine
• Billet construction huge strength upgrade over stock cast unit
• Utilizes OEM rubber coupler
• A must for any High Horsepower/ Race watercraft

Description 

Yamaha Dual fitting pump cooling plate kit. Billet anodized plate that fits directly onto OEM Yamaha Jet unit, allowing 2 extra water fittings to be added to your watercrafts cooling system. A must for High horsepower applications.

BRASS FITTINGS NOT INCLUDED.

Description 

This complete kit includes (10) Washers, (10) Studs and (10) Nuts. Constructed from premium 8740 alloy our Stud Kit will provide more accurate and consistent torque loading

A must have for any engine re-build or performance modifications!

Kit includes 10 x stud/nut/washer. Picture for illustration purpose only

Description 

This complete kit includes (10) Washers, (10) Studs and (10) Nuts. Constructed from premium 8740 alloy our Stud Kit will provide more accurate and consistent torque loading.

A must have for any engine re-build or performance modifications!

Kit includes 10 x stud/nut/washer. Picture for illustration purpose only

Description 

• In the tank, replacement increases fuel pressure approx 10psi
• Cost effective alternative to External fuel regulator
• Ideal for Low boost applications and reflashed/ aftermarket ECU

Description 

Allows for easy installation of extra cooling lines.
1/2 inch.

WORX Racing Yamaha 1.8 engine cooling upgrade kit provides the much needed extra cooling when modifying your watercraft. Our WORX Racing cooling kit allows the addition of an extra water line from the Jet unit which feeds directly into the Yamaha 1.8 engine block to significantly lower engine temperatures under load to increase engine reliability and performance.

Kit includes all necessary fittings, hoses, and clamps you need.  

1/2 hose and fittings. Suitable for Stock and mild applications (eg. filter, reflash, etc.)

A must for skis with re-programmed ECU and higher RPM limit

NOTE: DOES NOT suit 2018+ YAMAHA MODELS WITH NEW PUMP STRAINER THEY REQUIRE WR04018 KIT

Description 

Yamaha Pump Plug Kit WR0703, Improves pump intake dynamics by changing the shape and flow of the standard pump intake system.

This kit goes perfectly with the Worx Scoop Grate WR237 (also for the Yamaha 2012,2013,2014 FX, FX SHO.)

The Kit is easy to fit and provides an immediate improvement on stock.

Description 

Larger openings for increased water flow into the engine for lower engine temps

Suits any late model 155mm jet unit

• Constructed from Marine Grade 6061 Aluminum for superior strength
• Retains original throttle/steering sensors
• Designed for racing and can be used for recreational, too
• Fits 7/8 handlebars allowing you to select the style of bars that suit your own unique riding style
• Black anodized
• Comes with billet cover plates for a sleek design look

This steering stem will fit 2008-2011 FX but the cover plate will need modification to fit these models

Description 

*Suits all 1.8 Naturally aspirated engines 

Allows for maximum Air Flow to your engine

* Increased acceleration and overall RPM's

* Race proven design a must for any Modified/ Race watercraft

* Engine Breather Filter also provided in the kit

Description 

Billet Anodized Construction

Replaces expensive OEM rubber part which can fail and lead to boost leaks on S/C models

Comes with all hardware, gasket, and O-Rings for installation

Suits all Yamaha 1.8 Waverunners

Description 

Designed not just for cutting edge performance but killer style! Same best selling Worx Racing paddle now with billet insert for 4 point adjustment to personalize your watercraft to your own unique riding style! 

Specifically designed for the unique handling characteristics of the Yamaha FX and FZ hulls.

Includes backing rails and all necessary hardware.

Product benefits include:

- Enhanced control, stability and predictability, the ski stays hooked and does not throw you off
- Stops the ski from sinking in the back in tight turns like stock sponsons
- Allows for Greater corner entry speed
- Maximized top speed performance by creating less drag
- Superior straight line stability
- Easy installation to stock mounting points

Currently Used by Deans Team Factory Yamaha Race Team, Aero Asqa, Chris MacClugage, Aus Pro stock national Champion Mitch Wayt, PTS Racing Enduro Team's Christian D'Agostin

IJSBA legal for all classes

Description 

Create more bow lift for less hull drag and increase in top speed

One piece billet anodized construction.

Allows removal of restrictive sound suppression baffles in the exhaust.

This part requires no drilling of holes by utilizing the OEM outlet in the pump tunnel. No modification of OEM hoses is needed so the ski can be returned to stock. The billet anodized outlet fits directly into OEM location.

This is a must for any modified personal watercraft.

Description 

Billet anodized construction

Allows fitment of 130mm ODI lock grips

Easy install

Billet endcap design to prevent grip sliding off if lock clamp fails

Included hardware 

NOTE: Grips NOT Included 

Description 

Specifically designed for the 2012 Yamaha FX SHO hull.

Benefits include:

- Closed Course and Offshore Race tested and proven Used by Chris MacClugage in 2016 P1 Aqua X skis built by the factory Yamaha Deans team!!!

- Superior hook up

- Better bow lift for top speed 

- Smoother turning

- Utilize WORX Pump Plug kit WR0703