Broward Motorsports Racing Yamaha SVHO/SHO TiAL Blow-Off Valve Kit
Improve your superchargers clutch life and reliability with this BMS Racing 50MM Blow-Off Valve Kit. Blow-Off unwanted boost pressure during off-throttle operation. This kit will help with supercharger clutch and gear life.
-BMS Racing 50mm TiAL Blow-off valve the biggest in the industry
- 4-Ply silicone hose
-Aluminum mounting flange machined with grooves to guarantee it won’t slide out.
-Get greater reliability by reducing wear to your clutch and engine components.
-Works on all Yamaha supercharged skis from 2008-present SVHO/SHO.
NOTE: Must remove stock plastic air box in order to use this BMS Racing Blow-off valve kit. Can upgrade to a WORX Racing Air Filter Kit WR04020
BMS Racing Yamaha Titanium Valve Retainers Kit 1.8L SVHO/SHO
BMS Racing titanium valve retainer upgrade kit. This kit increases the reliability of your engine by reducing the possibility of valve float at higher than stock rpm. The kit Includes 16 lightweight titanium valve retainers. A must for Yamaha’s 1.8L motors that are revving higher then 8500 RPMS.
All 2008 - 2020 1.8L SVHO/ SHO / 1.8L HO Motors
BMS Yamaha FX SVHO 2019-2020 Stage 1 Tune
Unlock the full potential of your watercraft with our ECU Reprogramming Service.
Flash tuning is a process where your watercraft ECU can be re-programmed, to obtain the full potential of your watercraft engine.
Upgraded tuning parameters:
Increase Horsepower by improved fuel and timing maps
No engine internal modifications required
Improve throttle response
Enhance efficiency through all RPM
Increase rev limiters
Increase torque through entire powerband
Improve throttle control & reaction
Increase top speed
For 93 octane pump fuel
Please specify your modifications and performance goals.
PLEASE NOTE: This is an ECU reflash service performed on your stock ECU.
Once you place your order please wait for an email from our C.M.S Customer Service Team with details on where to ship your ECU and a form to be sent with it.
C.M.S. will perform this service the same or next business day the ECU is received and will return your ECU to you via a fully trackable overnight service.
Fizzle Y1000 Yamaha Intercooler Kit w/ TiAL BOV, or HKS BOV
Includes authentic TiAL or HKS (your choice) blow off valve
Gain 2-3+ MPH top speed over OEM Yamaha SHO or SVHO intercooler
Gain 200-300+ peak RPMs, acceleration and throttle response
Kit Contents: The intercooler with blow-off valve flange, full piping kit, mounting bracket system, and cooling line fittings
Fits all supercharged Yamaha watercraft 2008-2019, including FZR, FZS, GP1800, FX SHO, and FX SVHO models and supercharged Yamaha Jet Boats
Solas Yamaha 160MM Concord 13/18 Impeller
The new Solas Concord YV-CD-13/18 blows away the performance of your stock impeller! Large blade area and superior hub design deliver increased acceleration and top speed.
Solas Yamaha 160MM Concord 13/20 Impeller
The new Solas Concord YV-CD-13/20 blows away the performance of your stock impeller! Large blade area and superior hub design deliver increased acceleration and top speed. This 13/20 variable pitch impeller works great with stock through Stage 2 modifications.
2019 FX HO/ SVHO Non Cruiser Jet Trim Seat Cover
Fits 2019 Yamaha FX HO and FX SVHO non-cruiser models.
Please call 800-940-3000 or email firstname.lastname@example.org for custom orders.
Constructed from Marine Grade 6061 Aluminum for superior strength
Retains original throttle/steering sensors
Designed for racing and can be used for recreational, too
Fits 7/8 handlebars allowing you to select the style of bars that suit your own unique riding style
Comes with billet cover plates for a sleek design look
This steering stem will fit 2008-2011 FX but the cover plate will need modification to fit these models
FX, FX SHO, 2014+ FS SVHO Intake Grate
Specifically designed for the 2012 Yamaha FX SHO hull.
- Closed Course and Offshore Race tested and proven Used by Chris MacClugage in 2016 P1 Aqua X skis built by the factory Yamaha Deans team!!!
- Superior hook up
- Better bow lift for top speed
- Smoother turning
- Utilize WORX Pump Plug kit WR0703
2012+ FX, FX SHO, 2014+ FX SVHO Pump Seal Kit
Yamaha Pump Plug Kit WR0703, Improves pump intake dynamics by changing the shape and flow of the standard pump intake system.
This kit goes perfectly with the Worx Scoop Grate WR237 (also for the Yamaha 2012,2013,2014 FX, FX SHO.)
The Kit is easy to fit and provides an immediate improvement on stock.
ET 17lb Billet Supercharger Wheel SVHO
Engine-tech has been working on this project for quite some time and is now complete. The results are outstanding 17 lbs of boost @ 8500 rpm. Machined from billet 7075-T651 using a 5 axis CNC machining center allows a blade accuracy of .001. Balance to a spec of .009 inch gram and comes completely anodized gold for protection against the elements(corrosion resistant)
WORX Yamaha Engine Cooling Kit
Suits all SVHO Yamaha models including 2018+ models with updated pump strainer
WORX Racing Yamaha 1.8 engine cooling upgrade kit provides the much needed ‘extra cooling’ when modifying your watercraft. Our WORX Racing cooling kit allows the addition of an extra water line from the Jet unit which feeds directly into the Yamaha 1.8 engine block to significantly lower engine temperatures under load to increase engine reliability and performance. Hi-flow intake screen allows for an increase in water flow levels to all engine and associated components.
Kit includes all necessary fittings, hoses, gaskets and clamps, bolts you need.
1/2 inch hose and fittings. Suitable for Stock and mild and heavily modified applications (eg. filter, reflash, upgrade supercharger, etc.)
A must for skis with re-programmed ECU and higher RPM limit, or operating in hotter climates.
WORX Yamaha Engine Cooling Kit
WORX Racing Yamaha 1.8 engine cooling upgrade kit provides the much needed extra cooling when modifying your watercraft. Our WORX Racing cooling kit allows the addition of an extra water line from the Jet unit which feeds directly into the Yamaha 1.8 engine block to significantly lower engine temperatures under load to increase engine reliability and performance.
Kit includes all necessary fittings, hoses, and clamps you need.
1/2 hose and fittings. Suitable for Stock and mild applications (eg. filter, reflash, etc.)
A must for skis with re-programmed ECU and higher RPM limit
NOTE: DOES NOT suit 2018+ YAMAHA MODELS WITH NEW PUMP STRAINER THEY REQUIRE WR04018 KIT
WORX Yamaha SVHO pump strainer
Larger openings for increased water flow into the engine for lower engine temps
Suits any late model 160mm jet unit
WORX Yamaha Engine Cooling Adapter/Anodized
Billet anodized fitting to replace anode block which allows for extra cooling water to be added or removed from the rear of Yamaha 1.8 Engine block to suit your cooling needs. A must for any modified recreational or race craft.
ARP Flywheel bolt kit
High Strength Bolt kit for direct replacement of OEM Flywheel bolts that are prone to failure on modified watercraft.
Suits all Yamaha 1.8 models
Suit SeaDoo 4-tec 1503 and 1630 ACE engine
Sold in Pack of 6
Yuasa Lead Acid Battery YB16CL-B
Yuasa lead acid batteries are standard equipment on all Yamaha Watercraft. Batteries are activated with a wet acid (not included if shipped) and must be charged before use. Can be shipped UPS dry.
New Yamaha Genuine OEM replacement oil pump gasket. Required when replacing the supercharger clutch. Used on all Yamaha 1.8L engines.
WORX Yamaha Fuel Pressure Reg 1.8L
In the tank, replacement increases fuel pressure approx 10psi
Cost effective alternative to External fuel regulator
Ideal for Low boost applications and reflashed/ aftermarket ECU
WORX Yamaha Pump Cooling Plate Dual
Yamaha Dual fitting pump cooling plate kit. Billet anodized plate that fits directly onto OEM Yamaha Jet unit, allowing 2 extra water fittings to be added to your watercrafts cooling system. A must for High horsepower applications.
BRASS FITTINGS NOT INCLUDED.
WORX Yamaha Trim Extension All RiDE models only NEW
Fits 2015+ Yamaha VXR and 2015+ Yamaha FX SVHO
Increases trim range to bring the nose of your boat higher and increase speed!
Note: Only Suits Yamaha Models WITH RiDE System
Billet Engine coupler 2008+ FZR, FZS, FX, FX SHO
Billet Drive coupler for Yamaha 1.8 Engine
Fits any 1.8 Yamaha Engine
Billet construction huge strength upgrade over stock cast unit
Utilizes OEM rubber coupler
A must for any High Horsepower/ Race watercraft
WORX Yamaha Case Stud Kit (ARP) Yamaha 1.8 HO/SVHO
This complete kit includes (10) Washers, (10) Studs and (10) Nuts. Constructed from premium 8740 alloy our Stud Kit will provide more accurate and consistent torque loading
A must have for any engine re-build or performance modifications!
Kit includes 10 x stud/nut/washer. Picture for illustration purpose only
WORX Yamaha Blow Off Valve Assembly 1.8L SHO/SVHO
Our cost-effective design BOV will greatly improve supercharger clutch life in your Yamaha 1.8 engine. Kit includes a High Strength silicone hose that incorporates a Billet lightweight “Blow off Valve’, necessary vacuum lines and fittings for install.
Easy install to OEM location
Lightweight billet construction less load on the hose to reduce fatigue and tearing
Easy to disassemble for cleaning and maintenance
Cost effective upgrade for stock or modified skis
WORX Yamaha 1.8L bar extension suit OEM bars/ODI grips
Billet anodized construction
Allows fitment of 130mm ODI lock grips
Billet endcap design to prevent grip sliding off if lock clamp fails
NOTE: Grips NOT Included
WORX Yamaha 1.8L Pump wedge
Create more bow lift for less hull drag and increase in top speed
One piece billet anodized construction.
WORX Through hull fitting 1/2inc
Allows for easy installation of extra cooling lines. 1/2 inch.
2008+ FX, FX SHO, FZR, FZS, VXR, VXS
Tapered offset to match OEM reduction nozzle
Creates even pressure in reduction nozzle too reduce pump cavitation
Increased acceleration, drive and top speed
Suits all ‘3 bolt’ 1.8 Yamaha pump models
WORX Yamaha 1.8L Intercooler Kit
The WORX Racing Components Yamaha Intercooler kit features a New High Flow High capacity intercooler unit capable of handling up to 500 HP!!! A huge internal core almost twice the size of the inefficient OEM cooler allow maximum airflow for any high boost application allowing for increased RPM and dramatically lowering intake air temperatures up to 22C/72F degrees cooler than OEM unit. The upright element design in which water flows from Bottom of the Intercooler to the top allows an extremely efficient heat transfer allowing more cooler, denser air to enter the engine for increased HP throughout the entire RPM range which can add an extra 45+HP to your watercraft in certain applications.
The WORX Racing Components Intercooler Kit comes complete with removable adjustable Blow off Valve (included), Formed silicone hoses to allow easy access and fitment, all necessary mounting hardware and brackets to mount cooler securely. Also included is complete ‘Cooling Upgrade Kit’ which allows an extra dedicated water cooling line to the Intercooler from the Jet unit and an additional engine block cooling plate to add more water to the engine block to help decrease core engine temps.
New Anodised core!!!!
Huge internal core element for increased airflow and denser air
Extremely lower air intake temps over OEM cooler
Huge HP gains up to 45+ Horsepower in certain applications
Removable bracket, silicone hoses, and necessary hardware all INCLUDED for easy install
Upright element and water flow for increased heat transfer and efficiency
Upright mounting allows water to completely drain from the unit after use
Blow off Valve INCLUDED in the kit to help supercharger reliability and performance
Complete Independent Intercooler cooling kit upgrade for lower air temps
Note* May required adjustment of reverse cable mounting for early model FX 08-11
ET 20lb Billet Supercharger Wheel SVHO GEN 2
Yamaha SVHO E-T S/C Wheel
ET 20LB GEN2 Billet Supercharger Wheel
Yamaha SVHO FZR FZS S/C 20lb GEN2 15 g lighter
Race proven the ultimate limited Supercharger wheel.
Engine-tech has been working on this update and is now complete. The results are better that the old 19 lighter 15g less heat out and increased midrange and top-end. Better performance with longer clutch life. 20 lbs of boost @ 8500 rpm. Machined using 5 axis CNC machining center allows a blade accuracy of .0002. Balance to a spec of .009 inch gram and comes completely anodized gold for protection against the elements(corrosion resistant).
Requires an aftermarket shaft.
ET SVHO 24lb GEN2 wheel
Yamaha SVHO E-T S/C Wheel
ET 24LB GEN2 Billet Supercharger Wheel
Yamaha SVHO FZR FZS S/C 24lb GEN2 14 g lighter
Race proven the ultimate limited Supercharger wheel.
Engine-tech has been working on this update and is now complete. The results are outstanding lower out temps increased midrange and more boost. Lighter by 14 grams to increase clutch life. 24 lbs of boost @ 8500 rpm. Machined using a 5 axis CNC machining center allows a blade accuracy of .0002. Balance to a spec of .009 inch gram and comes completely anodized gold for protection against the elements(corrosion resistant).
Requires a aftermarket shaft.
ET SVHO 26lb GEN2 wheel
Yamaha SVHO E-T S/C Wheel
ET 26LB GEN2 Billet Supercharger Wheel
Yamaha SVHO FZR FZS S/C 26lb GEN2 14 g lighter
Race-proven the ultimate limited Supercharger wheel.
Engine-tech has been working on this update and is now complete. The results are outstanding lower out temps increased midrange and more boost. Lighter by 14 grams to increase clutch life. 26 lbs of boost @ 8500 rpm. Machined using a 5 axis CNC machining center allows a blade accuracy of .0002. Balance to a spec of .009 inch gram and comes completely anodized gold for protection against the elements(corrosion resistant).