Fitment

• 1996-2004 Yamaha

The OEM sponsons are a joke! They look adjustable but aren't and are fixed at the rear of the rail which gives the best top speed in only flat calm water, even in a light chop the boat bounces all over the place. It is hard to control and loses drive because the pump is out of the water more than it is.

But don't worry, WORX have saved the day!
The WORX Sponsons are truly adjustable only the full length of the backing rail as well as two different heights. The hull is the most reactive to sponson position that we have ever tested, for maximum top speed in calm water the sponson blades are best fitted in the fully forward position but even in the slightest chop the boat bounces all over the place. For maximum handling and hook-up on the race course, the fully back position is best but you sacrifice 1-3MPH (depending on the weight of the rider) because the boat rides a lot flatter. The ideal position is somewhere in between fully back and fully forward but is dependent on the rider weight, riding style and the type of riding that they are doing.

Note: Before purchasing, check below that your OEM sponson mounting bolts match the backing rail bolt layout pictured below.

Fitment

• 2001-2005 Kawasaki

Description

This ride plate is a direct bolt on replacement for all recreational or competition SXI Pro's and SXR 800's allowing most riders to ride faster while expending less energy.

The plate is considerably longer then the OEM plate with our trademark 'D' cut in it, the extra length of the plate holds the boat flatter and stops porposing, the 'D' cut makes a big difference to the handling in several ways:
1. It helps to hold the boat flatter in rough water and under initial acceleration, as the bow lifts, the 'D' cut out bites into the water pulling the boat back down which let's the pump get better hook-up and drive
2. When you are cornering hard the 'D' cut out keeps the boat more stable by allowing water to travel over the top of the plate through the cut-out

Instructions

Fitment

• 2000-2002, 2006-2011 Kawasaki

The largest of the Kawasaki range, the STX introduced in 2000 as a two stroke and then in later models fitted with the 12F and 15F four stroke engines these boats really benefit from an efficient intake grate to properly load the pump and get the best from your Kawi.
Performance benefits include:
- Better hook up in all conditions
- No top speed loss
- Better pump loading in rough water
- Holds the boat on the water giving better control
- Better cornering because the Worx grate has two rails running the full length that hang down 12mm below the pump cavity which stop the boat sliding out

Instructions

Fitment

• 1997-2020 Kawasaki

Want to revive your old ski? Looking for a way to reignite your passion for the water? Look no further than Worx WR527-I Sponsons!

Made for Kawasaki STX12F and 15F Sponsons models, these sponsons have been specifically designed to improve the handling performance of your Kawasaki ski. 

Designed for full adjustability, these sponsons put your ride, completely in your hands! Not only is the paddle height adjustable but the forward and backward positioning options means that, for maximum top speed in calm water you can position your blades in the fully forward position or for maximum handling and hook up the fully back position is best!

All Worx Sponsons are designed and manufactured in our Australian warehouse on the Gold Coast, so when you buy Worx Sponsons, you can be sure that you're supporting an Australian owned business. 

Features:

• Improved direct response in cornering
• More predictable handling
• Greater straight line stability
• Made in Australia

Includes:

• 2 x Backing Rails
• 2 x Paddles
• All Fasteners Needed

Note: Before purchasing, check below that your OEM sponson mounting bolts match the backing rail bolt layout pictured below.

Instructions

Fitment

• 1997-2010 Kawasaki

Fitment

• 1997-2006 Kawasaki

This ride plate is a direct bolt on replacement for all recreational or competition SXI's allowing most riders to ride faster while expending less energy.

- Extra length holds the boat a lot flatter
- Hard chine lines on the edges of the plate make it a lot easier to carve those really tight turns in complete control
- Incorporates our famous 'D' cut which picks up water when you push the boat in hard turns and gives it a lot more stability and less tendency to slide out. The bevelled edge on the 'D' cut-out help to hold the boat flatter and gives you a lot better drive and control.

Instructions

Fitment

• 1987-1997, 1999-2002 Kawasaki

These Kawasakis are super fast. However, in standard form they don't hook up and are downright scary to ride at full speed. They are very unpredictable and tend to track on waves of boat wake.
Problem solved! The Worx grate helps with hook up and overcomes the stability issue without causing any speed loss in calm water conditions. Add a set of Worx WR519 to completely transform the handling of your boat.

Instructions

Click Here To Download WR215 Instructions

Instructions

Fitment

• 1999-2005 Kawasaki

Bored of the way your ski currently handles? Want to corner tighter and faster? Make your jet ski feel like it's turning on rails with Worx Racing Component's WR508 Sponsons.

Made for Kawasaki ZXI 900/1100 models, these sponsons have been specifically designed to improve the handling performance of your Kawasaki ski. 

Expect greatly improved direct response in cornering, more predictable handling AND greater straight line stability, especially in rough conditions.

All Worx Sponsons are designed and manufactured in our Australian warehouse on the Gold Coast, so when you buy Worx Sponsons, you can be sure that you're supporting an Australian owned business. 

Features:

• Improved direct response in cornering
• More predictable handling
• Greater straight line stability
• Made in Australia

Includes:

• 2 x Backing Rails
• 2 x Paddles
• All Fasteners Needed

Note: Before purchasing, check below that your OEM sponson mounting bolts match the backing rail bolt layout pictured below.

Fitment

• 1995-2003 Kawasaki

This intake grate combats the boats tendency to porpoise when you are riding two up, holding the boat a lot flatter on the water and will improve handling and hook up. Combine with Worx Sponsons WR513 for ultimate handling and performance.

Instructions

Fitment

• 1995-2006 Kawasaki

Fitment

• 1996-2005 Sea-Doo

This intake grate will improve the all round handling and performance of your boat in all water conditions without costing you any top end speed. Providing the ultimate hook up and increased top end speed, our WR208 is equally at home on a family weekender as it is on a full house competition race boat.

Instructions

Fitment

• 1996-2005 Sea-Doo

The Worx WR212 will give you great hook up in all water conditions with no cavitation off the mark no matter how hard you accelerate, and in the rough water you will gain drive and control.

Instructions

Fitment

• 1993-2003 Sea-Doo

The OEM grate is fine in flat calm water conditions but is not so good in choppy or rough water, the boat cavitates and looses a lot of drive which causes a drop off in top speed of several MPH.
Performance Benefits:
- No top speed loss
- Better hook up in all water conditions
- Better cornering because the Worx grate has two rails running the full length that hang down 12mm below the pump cavity which stop the boat sliding out

Instructions

Fitment

• 2002-2007 Sea-Doo

Fitment

• 1991-2011 Sea-Doo

Ready to unleash that signature throaty sound????? This rear exhaust kit delivers bold performance and an aggressive tone—whether you're tearing it up on race day or chasing thrills on the weekend.

Features:

? 2.5 inch black anodised billet outlet – built tough, looks tougher

? Moulded silicone hose – eliminates resonance for that deep, clean growl

? Standard outlet block-off included – everything you need in one kit

? Deletes factory sound suppression baffles – for unrestricted flow and max attitude

? Suitable for recreational and race skis

? Fits GTR, GTI, RXPX T3 Hull, and early 4-Tec models

? Note: OPAS removal may be required prior to install

?? Does NOT fit S3 hull skis or new RXPX 300 models

This exhaust was originally designed for a 2012 RXPX. Fitment has been confirmed across many models. However, some recent models may require the alternate block-off kit (WR04013-2), which blocks the exhaust from the inside of the hull.

Disclaimer: Aftermarket exhausts (yep, including ours) are… wait for it… LOUD. If you like to make an entrance and be heard before you’re seen, you’re in the right place.

If your idea of fun is scenic detours and deep chats about fuel economy… stock’s probably more your speed ??

Instructions

Download Instructions

In testing we loved the speed of the RX but discovered that they do not hook up well in anything but perfect conditions. Our Worx Intake Grate will maximise hook up and stability without causing speed loss in calm conditions. Pair with our WR519 sponsons to totally transform the handling of your boat.

Instructions

Fitment

• 2000-2004 Sea-Doo

Fitment

• 2000-2002 Sea-Doo

Want to revive your old ski? Looking for a way to reignite your passion for the water? Look no further than Worx WR540-I Sponsons!

Made for Seadoo RXP/RXT/GTX/GTI models, these sponsons have been specifically designed to improve the handling performance of your Seadoo jetski. 

Expect greatly improved direct response in cornering, more predictable handling AND greater straight line stability, especially in rough conditions. 

With the adjustability of four positions, you can tailor the positioning to your riding style!

All Worx Sponsons are designed and manufactured in our Australian warehouse on the Gold Coast, so when you buy Worx Sponsons, you can be sure that you're supporting an Australian owned business. 

Features:

• Improved direct response in cornering
• More predictable handling
• Greater straight line stability
• Made in Australia

Includes:

• 2 x Backing Rails
• 2 x Adjustable Paddles
• All Fasteners Needed

Note: Before purchasing, check below that your OEM sponson mounting bolts match the backing rail bolt layout pictured below.

Instructions

Download Instructions

Fitment

• 2002-2010 Sea-Doo

Sea-Doo Start/ Stop switch housing

- Solid billet anodised construction

- Utilises small Sea-Doo Switch panel and late model (thick) red button

- 2 piece bar clamp style for adjustability

- Great for start/stop button on custom skis/ launch control button etc

- Can be used on either side of handle bars

Fitment

• 1989-2020 Sea-Doo

These hull extensions bolt right into factory mounting holes to effectively extend the working length of your boat by approx. 20%. The difference is very noticeable, you get on the plane quicker, no more porposing in choppy water your boat will run straight and true with no top speed loss.

Instructions

Fitment

• 1991-2004 Sea-Doo

This grate is a must to get the best from your boat! Designed to give your pump excellent loading in all water conditions, it will not cost you speed in the calm and will make a night and day difference in choppy to rough conditions.

Instructions

Fitment

• 1991-2002 Sea-Doo

Want to revive your old ski? Looking for a way to reignite your passion for the water? Look no further than Worx WR511 Sponsons!

Made for Yamaha GP760, GP800 & GP1200 models, these sponsons have been specifically designed to improve the handling performance of your Yamaha jetski. 

Expect greatly improved direct response in cornering, more predictable handling AND greater straight line stability, especially in rough conditions. With the adjustability of three positions, you can tailor the positioning to your riding style!

All Worx Sponsons are designed and manufactured in our Australian warehouse on the Gold Coast, so when you buy Worx Sponsons, you can be sure that you're supporting an Australian owned business. 

Features:

• Improved direct response in cornering
• More predictable handling
• Greater straight line stability
• Made in Australia

Includes:

• 2 x Backing Rails
• 2 x Adjustable Paddles
• All Fasteners Needed

Note: Before purchasing, check below that your OEM sponson mounting bolts match the backing rail bolt layout pictured below.

Instructions

Fitment

• 1997-2002 Yamaha

Fitment

• 1996-2004 Yamaha

Not having a WORX intake grate on a Yamaha GP, is like having a high performance sportscar on a wet road with bald tyres, it is just not possible to get the best from these boats.
Performance benefits of our WR218 include:
- Better hook up in all conditions
- No top speed loss
- Better pump loading in rough water
- Holds the boat on the water better giving better control
- Better cornering because the Worx grate has two rails running the full length that hang down 12mm below the pump cavity which stops the ski sliding out

 Fits GP800R, GP1200R, GP1300R

Instructions

Fitment

• 2000-2008 Yamaha

WORX Yamaha superjet exhaust sleeve fits directly into the OEM exhaust muffler and reduces the stinger size of the pipe to create more back pressure in the pipe for increased top speed.

Used by all Pro National and World Lites class Champions 

Fitment

• 1990-2020 Yamaha
• 1990-2020 Yamaha Superjet

Fits 1991-2014 Superjets. Also fits Waveblaster 1 & 2. Designed with a deeper scoop for more aggressive hook up. Ideal for Freestyle, Freeride and Racing.
This is one of the first intake grates ever produced by Worx. It is used by many of the top racers and recreational riders world wide and is the most popular Superjet/Blaster Intake grate on the market. These boats cavitate easily and lose drive because of the relatively flat intake area, the WR201 will solve these issues and will take the handling capability of your boat to new levels. It is a great rough water and surf riding intake grate because the pick-up area is wide and deep. It not only loads the pump but it also allows you to ride hard up to a turn buoy and then when you come off the throttle, the grate acts like a brake to slow you into the turn. For dramatically improved hook up and turning look no further than Worx WR201.??

Instructions

Fitment

• 1990-2020 Yamaha
• 1990-2020 Yamaha Superjet

Sick of your stock plastic pump shoe bending, cracking, or breaking when you really put the pedal to the metal? Yeah, we get it. That's why we designed the Worx Racing cast aluminium pump shoe, the last pump shoe upgrade you'll need for your stand-up.

This thing can take the heat, the load, and the big hits from your freestyle engine. Our pump shoe is pre-drilled and tapped but as it is a cast part, some minor modifications may be needed.

Whether you’re pushing it to the limit or simply craving reliability, this pump shoe works with large winged aftermarket intake grates for max efficiency and zero sacrifice in performance. Fits all Yamaha Superjets and most aftermarket hulls.

? Tough as Nails – Cast aluminium construction built for high speeds and heavy-duty use.
? Max Efficiency – Works with aftermarket intake grates for ultimate jet pump performance.
? Built to Last – Say goodbye to plastic and hello to reliable, long-lasting strength.

Fitment

• 1990-2020 Yamaha
• 1990-2020 Yamaha Superjet, SHO

Worx Racing WR544 Yamaha Superjet Sponsons are designed specifically to increase the handling performance of Yamaha Superjet Jetski's. Easily one of the easiest parts to upgrade on your ski. Worx recommend sponsons as one of the first upgrades to your ski. 

Adjustable to individual riding style and ability, these Superjet sponsons are perfect for any Jetski enthusiast, whether you're just out on the weekend with your mates, or riding professionally. And because they're compatible with various aftermarket hulls, you can be sure they're the right call. 

Constructed from Marine Grade Aluminium, this sponson set will have you running rings around your mates!

Instructions

Fitment

• 1990-2020, 2023-2025 Yamaha
• 1990-2020, 2023-2025 Yamaha Superjet