Our oil catch can eliminates power-robbing blow by fumes and oil vapor from your engine's air intake tract. Also improves intercooler efficiency by preventing an oil sludge coating that saturates the inside of the intercooler. Excess oil vapor is routed to our stainless steel catch can where it collects for draining via petcock valve. Our catch cans also have Stainless steel wool inside to help with oil sloshing.

*Make sure your oil level isn't overfilled. This will cause Excess crank case pressure, this will fill the oil catch can and may spill oil over into the hull. Keep oil level just under the  top bend of your oil stick.

Check and drain during your service interval. We recommend 25 hours.

Kit includes:

Black Breather Filter

Stainless Steel Catch Can

3/4 Hose

Brass Petcock drain

FITS:

Seadoo 300 Models

• Improve reliability and performance by replacing the soft and flimsy stock rubber intercooler hoses with the Fizzle heavy duty reinforced tubing kit for your Sea-Doo 300 watercraft. Fits all Sea-Doo 300 watercraft RXP-X 300, RXT-X 300, GTX 300.

• Replaces stock hoses that are prone to bursting under heavy boost pressure

• Increased throttle response

• 5-ply heavy duty silicone construction

• Internal metal reinforcement

• Easier to install than stock rubber hoses and aftermarket piping kits

• High-quality marine grade 316 Stainless Steel hose clamps included

• Compatible with stock Sea-Doo 300 Intercooler, Fizzle SuperCooler, or Riva Gen. 4 Intercooler

• Tested on a heavily modified closed course Sea-Doo 300 race jetski with 23 PSI supercharger

Description

• Direct replacement for OEM Sea-Doo 300 HP intercoolers.

• Compatible with OEM Sea-Doo 300 HP rubber intercooler air hoses and Riva Gen. 4 intercooler piping kit

• Maximize throttle response and achieve lower Air Intake Temperatures (AIT)

• Eliminate intercooler heat fade

• Kit contents: Fizzle™ SuperCooler with waterline fittings and zinc anode

• Utilizes stock intercooler location, works with the stock exhaust system or aftermarket exhaust

• Designed for maximum horsepower capacity

• Integrated zinc anode for added protection against corrosion

Description

• Kit contents: Fizzle™ SuperCooler and Fizzle™ Sea-Doo 300 Intercooler Tubing Upgrade Kit: Intercooler waterline fittings and zinc anode, complete set of heavy-duty 5-ply silicone tubing with internal metal reinforcement, high-quality marine grade 316 Stainless Steel hose clamps.

• Direct replacement for full OEM Sea-Doo 300 HP intercooler system

• Maximize throttle response and achieve lower Air Intake Temperatures (AIT)

• Eliminate intercooler heat fade

• Utilizes stock intercooler location, works with the stock exhaust system or aftermarket exhaust

• Designed for maximum horsepower capacity

• Fits all Sea-Doo 300 watercraft RXP-X 300, RXT-X 300, GTX 300

Description 

• 16-16.5 lbs @ 8650 RPM
• 18lbs @ 9000rpm
• Kit comes with Impeller, spacer and modified front housing
• NOTE: REQUIRES MACHINING OF REAR HOUSING

Description

11 lbs of boost @ 8100 rpm and 12.5 @ 8600rpm There is no other drop in that is even close to the acceleration and boost of this S/C impeller setup (42lb injectors)

Description 

ET 137 4MM CR Drop in Wheel for the 255/260. Light edition Billet impeller with 4mm spacer. This is a completely new design from the ground up taller blade hight, lighter, New aggressive blade geometry. There is no other drop-in Wheel that is even close to the acceleration and boost of this ET S/C impeller setup. You will have to add a fuel pressure regulator. Not included. most all 260's come with 48lb injectors. If you have a 255 then you may also have to add 48lb injectors depend on the year. Not included.

13 to13.5lb of boost @ 8100 rpm and 15lb + @ 8500rpm

(Clutch slip must be set to 15-foot lbs and 48lb injectors.) Includes 4mm spacer.